PLEASE NOTE 'SPARES' ARE ONLY SUPPLIED TO FULLY PAID UP MEMBERS OF THE CLUB . PARTS MUST BE ORDERED USING OUR SPARES ORDER FORM AND QUOTING YOUR CLUB MEMBERSHIP NUMBER. THE LIST BELOW SHOWS THE FULL RANGE OF NEW AND REMANUFACTURED PARTS AVAILABLE TO MEMBERS.
PLEASE NOTE THAT DUE TO INSURANCE STIPULATIONS WE ARE NO LONGER ABLE TO SUPPLY PARTS TO MEMBERS LIVING OR RESIDING IN U.S.A OR CANADA.
Spare Time
Stock List For 2007
| ENGINE AND CLUTCH: | GEARBOX AND TRANSMISSION: |
| Oil filter (long) 5 1/2" (14 cm) bowl | Universal Joint |
| Oil filter (short) 4 1/2" (11 1/2cm) bowl | Gearbox mounting |
| Three long oil filters | Gearbox rear housing bush |
| Oil pressure switch (spade or screw connector fitting) | Speedometer cable |
| Valve (inlet or exhaust) (standard/+3 thou/+15 thou) | |
| Valve springs (per set of 8) | |
| Timing chain | |
| Timing chain tensioner | GASKETS AND SEALS: |
| Core plug (each) | Head set (head gasket and everything above) |
| Piston assembly (standard/+20"/+30"), per set | Block set (everything below the head gasket) |
| Big-end shell bearings (standard)+.010"/+.020"/+.030"/+.040"), per set | Sump gasket set |
| Main crankshaft shells (standard)+.010"/+.020"/+.030"/+.040"), per set | Head gaskets |
| Crankshaft thrust washers (standard/+.005"/+.0015"/+.0025") | Rocker cover gaskets |
| Manifold gasket | |
| Tab washer (camshaft sprocket) | Thermostat gasket |
| Tab washer (flywheel locking plate) | Water pump gasket |
| Tab washer (engine mounting to block) | Sump plug |
| Tab washer (engine mounting to cross member) | Crankshaft pulley oil seal |
| Engine mounting | Timing cover gasket (with water pump) |
| Cam followers (per set of eight) | Timing cover gasket (without water pump) |
| Starter motor | Speedo drive gasket |
| Flywheel ring gear | Speedo drive oil seal (O" ring) |
| Snail spring cam for timing chain tensioner | Gearbox front oil seal (not 997cc usually) |
| Piston rings (per set) standard only | Gearbox rear oil seal |
| Gearbox gasket set | |
| Clutch cover assembly | Pinion oil seal |
| Clutch disc (driven plate) | Differential gasket |
| Clutch release bearing | Half shaft oil seal |
| Clutch release bearing carrier | Front hub oil seal |
| Spring and rivets for clutch release bearing carrier | Fuel tank sender unit gasket |
| Clutch Hose (righthand drive) nylon one piece | Fuel pump gasket (paper) per 2 |
| Clutch Hose (lefthand drive) nylon one piece | Fuel pump insulator (thick - engine to block) |
| Clutch slave cylinder | Steering box drop arm oil seal |
| Clutch slave cylinder repair kit | |
| Clutch slave cylinder return spring | |
| Slave cylinder clutch adjustment rod | |
| Master cylinder repair kit (As BR17) | |
|
|
G SYSTEM:
| ELECTRICAL AND SWITCHES: | COOLING SYSTEM : |
| Points set | |
| Points set (Lucas) | Water pump - PLEASE RETURN OLD UNITS |
| Rotor arm (Lucas) | Water pump elbow (to heater) |
| Condenser (Lucas) | Fan belt |
| Distributor cap (Lucas, side entry) | Radiator cap (7 psi long) |
| Distributor cap (Lucas, top entry) | Radiator cap (10 psi short) |
| Spark plug leads (Lucas, side entry) | Thermostat (82 degrees C) |
| Spark plug leads (Autolite and Lucas, top entry) | Thermostat (88 degrees C) |
| Points set (Autolite) | Thermostat (92 degrees C) |
| Rotor arm (Autolite) | Top radiator hose |
| Condenser (Autolite) | Bottom radiator hose |
| Distributor cap (Autolite) | Temperature sender large diameter (1/2" thread) |
| Voltage regulator (two bobbin type, inside car) | Temperature sender small diameter (3/8" thread) |
| Voltage regulator (three bobbin type, inside engine bay) | Heater hose (to water pump) with jubilee clips |
| Dynamo brush set | Heater hose (to engine head) with jubilee clips |
| Starter motor brush set (both starter types - M35G/M35J) | Thermostat housing |
| Ignition coil (screw-in top - early type) | |
| Ignition coil (push in - late type) | |
| Flasher unit (indicators) | |
| Spark plugs (per set of four) | |
| Temperature gauge assembly |
| CARBURETTOR AND FUEL SYSTEM: | EXHAUST SYSTEM: |
| Gaskets for B30 ZIC-3 (997cc) Solex | Saloon stainless steel rear pipe |
| Gaskets for B30 PSEI-3, -2 (997cc, 1198cc carbs) | Estate stainless steel rear pipe |
| Accelerator pump diaphragm (997cc, 1198cc) Solex | Van stainless steel rear pipe |
| Economiser diaphragm (PSEl-2 1198cc carbs) | Van stainless steel front pipe |
| Gaskets for FoMoCo carburettor | 997cc stainless steel front pipe (Saloon/Estate) |
| Accelerator pump diaphragm, FoMoCo | 1200cc stainless steel front pipe (Saloon/Estate) |
| Air cleaner sealing rings (PSEI-2, -3 carbs) | Tail exhaust strap |
| Air filter (cylindrical or folded types) | Central exhaust strap (Saloon, Estate and Van) |
| Fuel pump | Exhaust manifold clamp |
| Glasstop fuel pump | Chrome trim pipe (for exhaust tail pipe) straight |
| Fuel pump repair kit | Chrome trim pipe (for exhaust tail pipe) curved |
| Fuel pipe nut to tank (Saloon Van) | |
| Stainless steel petrol tank strap (Saloon left hand, shorter) | |
| Stainless steel petrol tank strap (Saloon right hand, longer) | |
| Petrol tank hook (Saloon - each) | |
| Petrol tank sender unit (Saloon or Estate) | |
| Olive - required to fix petrol pipe to caro/fuel pump (each) | |
| Nut (brass) - required to fix petrol pipe to carbifuel pump (each) | |
| Petrol Pipe (copper) (per foot or 30cm) |
| BRAKING SYSTEM: | SUSPENSION AND STEERING: |
| 997cc front brake shoes (axle set) - PLEASE RETURN OLD UNITS | Stud and bush (idler) joint |
| 997cc rear brake shoes (axle set) - PLEASE RETURN OLD UNITS | Idler bracket assembly (bracket and joint) |
| 1198cc front brake shoes (axle set) | Drag link |
| 11 9Bcc rear brake shoes (axle set) - PLEASE RETURN OLD UNITS | Track rod ends (per pair) |
| Handbrake cable (Saloon/Estate 997cc and 1198cc) | Track control arm (left hand) - PLEASE RETURN OLD UNITS |
| Handbrake cable (Van 997cc and 1198cc) | Track control arm (right hand) PLEASE RETURN OLD UNITS |
| Handbrake rear axle link support strap | Track control arm repair kit (ball joint etc) |
| Handbrake brake yoke re-inforcing plate) | Front suspension rubber bush kit (per side) |
| Copper brake pipe kits (Saloon/Estate Van/107E) | strut top mount |
| Front wheel brake adjuster set (axle set) | MacPherson strut |
| Rear wheel brake adjuster cylinder - either side | MacPherson strut insert - OUT OF STOCK |
| Rear wheel cylinder dust covers (each) | |
| Flexible brake hose (front) | Steering column felt brush |
| Flexible brake hose (rear) | Tab washer (bolts at strut base) |
| Master cylinder | Tab washer (stabiliser bar U-bolts) |
| Front wheel cylinder (left hand) | Stabiliser bar bolt, nut and washer (also for rear shock absorber) |
| Front wheel cylinder (right hand) | Rear damper (Saloon, left hand) |
| Rear wheel cylinder (either side) | Rear damper (Saloon, right hand) |
| Master cylinder repair kit | Rear damper (Estate, left hand) |
| Rear wheel cylinder repair kit (1 cylinder) | Rear damper (Estate, right hand) |
| Front wheel cylinder repair kit (2 cylinders) | Rear damper (Van, left hand) |
| Rear brake drum 997cc | Rear damper (Van, right hand) |
| Front brake drum 997cc | Rear spring front eye bush |
| Rear brake drum 1198cc - PLEASE RETURN OLD UNITS | Rear spring front eye bolt with nut and washer |
| Rear spring shackle rubbers (per set of 8) | |
| Automatic brake bleed valve | Rear spring shackle rubbers (each) |
| Stoplight switch (hydraulic system) | Front wheel bearing kit (one wheel) |
| Bleed nipples (per 2) (brake cylinder or clutch slave) | Rear wheel bearing - pre mid 1966 |
| Handbrake link (swivels through rear wheel cylinder) 997cc or l2OOcc each | Rear wheel bearing - mid 1966 on |
| Filler cap (master cylinder) each | Rear axle "U" bolts (per pair) |
| Front brake shoes return springs (axle set) per tour | Castle nut (fixes stabiliser bar to control arm) |
| Drop Arm (wide later type drop arm for steering box) | |
| Coil springs for front strut suspension (standard) per pair | |
| Coil springs for front strut suspension (heavy duty) per pair | |
| Strut Base Bolts (pack of 3) |
| BODY TRIM AND FITTINGS: | BODY PANELS: |
| Trim rivets (per 10) | PLEASE WRITE TO SPARES SECRETARIES (ENCLOSING SAE) FOR UP TO DATE DETALS OF PANELS AVAILABLE |
| Trim rivet adaptor (needed for pop rivet gun) | |
| Saloon/Estate Deluxe "dogleg (nearside) | |
| Saloon/Estate Deluxe "dogleg" (offside) | |
| Saloon Super "chevron" (nearside) | |
| Saloon Super "chevron" (offside) | |
| Deluxe pillar badge (one piece badge) each | |
| Super rear pillar badge base | |
| Badge plastic sleeve inserts (boot script badge etc) per 10 | |
| 'Anglia' script badge | |
| 'Deluxe' script badge | |
| Ford badge (rectangle, front wing) | |
| Trim buttons (kick panel etc) - black, per 10 | |
| Pedal rubbers (brake) | |
| Pedal rubbers (clutch) | |
| Clutch/brake pedal return spring | |
| Door check spring | |
| Door handle pad (to door screen) - per handle | |
| Rigid window channel- per piece (down quaterlight) | |
| Flexible door window channel - per door | |
| Door window weather strip - per 4 pieces | |
| Door window weather strip | |
| Spring clips for weather strips - per 5 · | |
| Spring clips for weather strips - each | |
| Door trim panel clips - per 10 oversize | |
| Door trim panel clips - per 10 standard - | LIGHTS AND LENSES: |
| Door seal - upper hall - per door, per piece | |
| Lower door seal (per piece) | Saloon rear indicator lens |
| Front windscreen rubber (Saloon/Estate) | Estate stop/tail lens |
| Rear windscreen rubber - Saloon | Estate rear indicator lens |
| Wiper arm (narrow L/H drive) 5.2mm | |
| Wiper arm (narrow R/H drive) 5.2mm | |
| Wiper arm (broad UK drive) 8mm | indicator/sidelight castings - with fitted double filament bulb holder (per pair) |
| Wiper arm (broad P/H drive) 8mm | Indicator castings - with fitted single filament bulb holder (per pair) |
| Wiper blade (for narrow wiper arms) | Estate rear light casting (not chromed) |
| Wiper blade (for broad wiper arms) | Van rear light casting (left hand) |
| Windscreen wiper splines, each | Van rear light casting (right hand) |
| Wiper sleeves for FoMoCo wipers (brass) | Front parking/indicator lens (left hand) clear |
| Bumper bolt (flat headed, chromed) | Front parking light/indicator lens (right hand) clear |
| Bumper bolt (high domed head, chromed) | Front parking lens (left hand) clear |
| Rubber piping for overriders (per piece) | Front parking lens (right hand) clear |
| Interior kick panel boards, per pair | Front indicator lens (left hand) amber |
| Bumper iron grommet NEW | Front indicator lens (right hand) amber |
| Ashtray spring and rivits | Headlamps (sealed beam - without sidelight holder) |
| Headlamp bowl (plastic) with chrome retaining ring and rubber gasket | Number plate light lens - twist type (early) |
| Gasket for headlamp bowl to body - rubber | Halogen headlamp (halogen bulb as LLi8 not included) |
| Gasket for front indicator unit to body (either side) - sponge | Halogen bulb (for use with LL17 headlamp) |
| Gasket for front indicator lens (either side) - sponge | |
| Gasket for front sidelight unit to body '65 to '67 (either side) - sponge | |
| Bootlid rubber seal | |
| Rear side window weather seal (Saloon) per window | |
| Grommet (grey) - rear side window - saloon | |
| Grommet - boot lid handle | |
| Grommet - wiper boss | |
| Grommet - bulkhead wiring loom -black | |
| Grommet - bonnet lid stop | |
| Grommet - inner wing wiring - black | |
| Grommets - blanking (rubber) 1" (26mm) or 3/4 (l9mm) per 5 | |
| Woven weathercord (around door opening) Grey/Black/Red, per door | |
| Bonnet hinge sleeve with nut | |
| Bungs for 10mm (3/8 inch) holes (for injecting Waxoyl) | |
| Wheel trims (per set of four) rectangle pattern | |
| Cigarette lighter (illuminated fittings) | |
| Front grille fastening clips (per 5) 8mm square hole | |
| Door quarter light rubber seals (per pair) | |
| section rubber bonnet seal (below windscreen) | |
| Fuel filler pipe grommet (rear panel, Saloon) | |
| Electric windscreen washer pump (with push button switch etc) | |
| Windscreen washer plastic tubing (per metre - 39") | |
| Handbrake lever gaitor | |
| Luggage compartment boards | |
| Overtaking mirror (stainless steel), fixes to quarter light window | |
| Holding clips for bonnet air vent (per 10) | |
| Estate tailgate window seal with chrome fillet insert | |
| Van rear door window seal | |
| Gasket for saloon rear stop / tail lens | |
| Gasket for saloon rear indicator lens | |
| Gasket for front sidelight lens 1965-67 | |
| Estate tailgate torsion springs | |
| Estate rear headlining clips | |
| Front grill indicator surrounds (per pair) for use with 3 piece grill | |
| Fog light brackets (tat iron bar type) each | |
| WING MIRRORS NOW AVAILABLE - SEND S.A.E FOR PRICES |
©2008 Ford Anglia 105e Owners Club Limited